Panther Motor Lifts and Mounts

Panther Motor Lifts Make your day on the water just a bit more enjoyable without straining your muscles trying to raise and lower the auxiliary motor. A simple convenience with major results.

	55-0035 Auxiliary Motor Lift Model 35 Make your day on the water just a bit more enjoyable with out straining your muscles trying to raise and lower the auxiliary motor. A simple convenience with major results. The heavy duty bracket easily handles auxiliary outboards up to 40hp or 150 pounds. Kicker motors are supported in any position with this durable design. In addition to its ruggedness, the Model 35 is the only kicker motor lift with a convertible setback. This unit can be adjusted to 13 inches of setback, making it ideal for inboards, I/Os, jet-drives, and outboards when over the transom mounting is unavailable. An optional spacer (55-9035) offers an additional three inches of setback for even greater clearance. When it comes to auxiliary motor lifts, the Model 35 sets the standard. Rugged, reliable, and tournament tested. 55-0350 Auxiliary Motor Lift Model 35LE The Auxiliary Motor Lift Model 35LE is the same rugged design as the powerful Model 35. The specially designed transom plate is made to fit the contoured transom of Ranger© and Lund © Pro V boats. Used by tournament fishermen all around the country the auxiliary motor lift is rugged, reliable, and tournament tested.

	55-0055 Trim and Tilt Model 55 Make your day on the water just a bit more enjoyable with out straining your muscles trying to raise and lower an outboard motor that is not equipped with trim and tilt. A simple convenience with major results. The compact Trim and Tilt Model 55 conveniently matches outboards from 15 to 55hp, weighing up to 250 pounds. Perfectly designed for pontoons, fishing, or pleasure boats. The Trim and Tilt provides and additional five degrees of negative tuck for an improved “hole” shot. Adapts to clamp on or bolt-through outboards.

	55-0135 Trim and Tilt Model 135 Make your day on the water just a bit more enjoyable with out straining your muscles trying to raise and lower an outboard motor that is not equipped with trim and tilt. A simple convenience with major results. The model 135 is the perfect option for older outboard motors with bad hydraulic trim and tilts, when repair costs are prohibitively expensive. The heavy duty bracket is designed for outboards up to 135hp or 350 pounds and it maximizes lifting power (even greater than the outboards tilt range), and it also allows for increased tuck-under to get heavy boats on plane quickly. Adapts to clamp on or bolt-through outboards.

	55-0435 Fixed Auxiliary Motor Bracket Model 435 This “fixed” Motor Bracket is designed for those rugged individuals who prefer to use their own strength to lift up their motors. It comes with the adjustable 13 in. setback feature and is made of 713 alloy aluminum.

	55-0405 Static Motor Mount Plate Model 405 If trolling motors are you thing – then our 405 static Plate is a must. It offers a sturdy and flat mounting area for your trolling motor clamps. Troll with confidence knowing that your trolling motor will stay where you put it!! This bracket makes mounting auxiliary and long shaft motors a snap. When direct to transom motor mounting is difficult, Panther’s Static Motor Mount Plate provides a flat secure mounting surface for clamp on or bolt on kicker motors up to 40 hp or 150 lbs. Made of solid cast aluminum with an 8 in. by 7 in. mounting area. The bracket can be used on most contoured boat transoms. The plate also works for mounting long shaft motors on short shaft transoms, because the plate set the motor 4 inches higher on the transom it’s perfect for Jon boats and small fishing boats when a short shaft motor would otherwise be required. Convenient economical durable and easy to install, the Model 55-0405 is the answer to difficult transom installations.

	55-1100 Universal Lift Gauge Maximize your boat’s performance with this electric analog gauge. This unit is truly universal and will fit any JackPlate or trim and tilt unit, providing accurate indication of the trim or tilt that is occurring. The 2 1/8 in. gauge matches most factory installation gauges. Contains gauge, sending unit, all wiring, and directions.

	55-9035 3 inch Spacer Kit for Model 35 lift This two piece, cast aluminum spacer provides an extra three inches of setback for the Model 35. I/O, jet drive, offshore, sailing, and other boat owners can now enjoy the convenience of hands-free kicker lifting. Impossible installations are a thing of the past. The spacer will extend the Model 35 to 16" of setback. Chromate dipped, powder paint coated for maintenance free durability. Questions? Call 651-486-2010